Klipper is een van de weinige 3D-printerfirmware die native ondersteuning biedt voor een externe camera om je 3D-printer te monitoren. De webinterface van Klipper maakt het eenvoudig om een camera aan de Raspberry Pi te koppelen en de voortgang van je printproces te volgen.

Klipper is echter een relatief nieuwe firmware met beperkte informatie en handleidingen die de verschillende functies beschrijven. Als nieuwe gebruiker of beginner is het gemakkelijk om in de war te raken over de installatie en configuratie van een camera op je Klipper 3D-printer.

Dit artikel is bedoeld om dit proces voor u te vereenvoudigen en u te helpen bij het instellen van een camera op uw Klipper-aangesloten 3D-printer. Lees verder voor een uitgebreide uitleg over de camera-installatieprocedure van Klipper en hoe een camera uw 3D-printworkflow kan verbeteren.

Inleiding​

Met de timelapse-functie van Klipper kun je je volledige 3D-printproces vastleggen en fragmenten ervan delen op je sociale media. Deze video's zijn ook een uitstekend hulpmiddel om printfouten te analyseren en de oorzaken van een mislukte print te achterhalen.

Ondanks hun nut kan het instellen van timelapse-video's in Klipper voor veel gebruikers een uitdaging zijn. En hoewel de installatie relatief eenvoudig is, kan de eerste configuratie beginners in Klipper gemakkelijk in de war brengen.

In dit artikel vereenvoudigen we dit proces voor u. We nemen de volledige procedure stap voor stap door en configureren de timelapse-functionaliteit voor uw Klipper-instantie. Aan het einde van deze handleiding kunt u perfecte timelapse-video's van uw 3D-prints opnemen en delen met uw sociale netwerk.

Laten we beginnen met filmen.

Nozzle Scraping Bed Surface​

What Is It?​

Inaccurate bed leveling, low initial layer height, or incorrect Z-offset settings can cause your printer's nozzle to scrape against the printing bed. It might damage the nozzle and the print bed and restrict the filament from flowing out of the nozzle.

If left unchecked for a while, it can build up pressure in the hot end and cause the extruder motor to skip steps. Nozzle scraping is relatively minor but one of the most common issues faced by beginners and new 3D printer users.

Blobs or Zits​

What Is It?​

Blobs or Zits are the tiny dots on your print's surface and directly affect its overall quality and appearance. These are often the result of incorrect retraction settings or high printing temperature and negatively affect the surface finish of your 3D printed part.

Sometimes, you can easily remove them with sanding, but big blobs can be challenging to remove and may leave an impression on your parts. For this reason, it's best to tune your printer to not create them in the first place rather than try to remove them through post-processing.

Broken Filament​

What Is It?​

The filament is a relatively fine plastic thread, which can break easily under certain conditions. If your filament breaks mid-way during a print, it will cause a print failure leading to a loss of print time and effort.

Filament usually breaks due to poor quality control, high humidity, or extreme tension in the filament path. These conditions are essential to consider if you're planning to print large-sized objects or want to use your printer for batch 3D printing.

Filament Stops Extruding Mid-Print​

What Is It?​

Your 3D printer can stop extruding filament mid-way during printing, leading to a failed print and losing printing time. The most likely and apparent reason might be your printer running out of filament material.

But, in some cases, nozzle clogs and defective extruders too can be a potential issue.

First Layer Issues​

What Is It?​

First layer issues reduce the chances of a successful print and are often the cause behind several failed 3D prints. Some of the significant and most common first layer problems are - prints not sticking to the bed surface, the first layer too rough, the nozzle not extruding filament or holes and lines in the bottom of your prints.

These problems can either affect the quality of your prints or cause them to fail, leading to loss of filament and printing times. Therefore, it's crucial to eliminate these issues and ensure a smooth and even initial layer.

Gaps in Print surfaces​

What Is It?​

Often 3D prints can have small visible gaps on their top surfaces, outer walls, and between the infill structure and the inner walls. These cavities ruin the appearance of your 3D-printed model and might also affect its structural integrity. Often, the cause behind gaps in your 3D prints is related to slicer settings, and you can quickly resolve these gaps by fine-tuning specific settings.

Inferior Surface Quality above Supports​

What Is It?​

Supports are essential to provide a base for the overhangs in your 3D prints. But incorrect support settings can affect your print's quality and appearance. If the top of your support is too close to the print's surface, it might leave marks and blobs. Whereas, if there's too much gap between the support and the print, you will encounter filament drooling and poor overhangs.

In an ideal scenario, the support should easily detach from the print's surface without leaving any marks. Moreover, the supported area of the print shouldn't indicate any filament drooling or signs of a support structure underneath it.

Inferior Surface Quality underneath Supports​

What Is It?​

With extreme overhangs, you need to use support structures that use the print's surface as their base. In such cases, the support pillars can adhere firmly to your print, affecting your part's surface quality. Less distance between the support base and the print can make removing the supports a challenge.

Popular slicers such as Cura and PrusaSlicer circumvent this issue using Tree Supportstructures. Tree supports have minimal contact with your 3D prints and help you achieve better-looking parts even with large overhangs.